Grand openingFull synthetic oil change $69.99 $114.99Book Now →

Why cold starts do most of the damage, and what oil has to do with it

What happens inside an engine in the first minute after a cold start, why it does so much of the wear, and how the right oil and a few habits protect it.

Why cold starts do most of the damage, and what oil has to do with it

What happens while the car sits

When the engine is running, the oil pump keeps a pressurized film of oil between every pair of moving metal parts: the crankshaft and its bearings, the camshaft and the valve train, the pistons and the cylinder walls. Those parts never actually touch. They ride on the oil, the way a tire can ride on a film of water.

Turn the engine off and the pump stops. Over the next few hours most of the oil drains back down into the oil pan at the bottom of the engine. A thin coating stays behind on the metal, along with the anti-wear additives that cling to it, but the full pressurized film is gone. By morning the engine is sitting mostly dry at the top and full at the bottom.

The first few seconds

When you turn the key, the engine starts turning immediately. The oil does not arrive immediately. The pump has to pull oil up from the pan, push it through the filter, and send it through the passages to the top of the engine. Until it gets there, the moving parts are running on whatever coating was left from yesterday.

On a warm day that gap is short. On a cold morning it is longer, because cold oil is thick. Oil that pours like water at operating temperature moves more like syrup at ten below, and the pump has to work harder to push it the same distance. That is the window where wear happens: metal parts moving with less protection than they will have a minute later. It is why you will often hear that most engine wear happens at startup. The exact share depends on the engine, the oil, and the weather, but the direction is not in doubt.

A couple of parts help close the gap. Most oil filters have a small rubber anti-drain-back valve that keeps the filter full while the car sits, so oil reaches the engine sooner. And the anti-wear additives in modern oil are designed to protect metal in exactly this moment, when the film is thin.

What the W on the jug is for

The viscosity grade on a bottle of oil, such as 0W-20 or 5W-30, is two numbers. The second one describes how thick the oil is at full operating temperature. The first one, with the W, is the cold rating. To earn a given W number, an oil has to pass two lab tests at low temperature: one for how easily the engine can crank through it and one for whether the pump can still move it. A 0W oil passes those tests at a colder temperature than a 5W oil does.

In plain terms: the lower the number before the W, the faster oil gets where it needs to go on a cold start. That is why so many newer cars call for 0W-20 or 0W-16, and why you should use the grade your owner's manual or oil cap specifies rather than a thicker one "for extra protection." Thicker oil is not more protection on a cold morning. It is a slower trip to the bearings.

Full synthetic helps here too. Its base oil is made of more uniform molecules than conventional oil, so it stays thinner in the cold without getting too thin when hot.

Cold starts also make the oil dirty

A cold engine runs a richer fuel mixture until it warms up, and some of that fuel gets past the piston rings and into the oil. Burning fuel also makes water vapor, and on a cold engine some of it condenses inside the crankcase instead of leaving through the exhaust. Once the engine is fully warm, the heat boils most of that water and fuel back out of the oil.

The trouble is the short trip. A four-minute drive across Marion to the school and back never gets the oil hot enough to clear itself. Do that every day in January and the fuel and water build up, the oil thins and loses some of its protection, and you may see a tan, milky film on the underside of the oil cap. That film is usually condensation, not a head gasket, but it is a sign the oil is working harder than its mileage suggests.

This is why many owner's manuals list frequent short trips in cold weather under severe service, with a shorter oil change interval. If most of your driving is short hops around Cedar Rapids in winter, check which schedule your manual puts you on. Our guide on how often to change synthetic oil in Iowa goes through how to read it.

What you can do about it

  • Use the grade the manual calls for. Not a thicker one in winter. The cold rating is the whole point.
  • Use oil that meets the spec on the cap or in the manual. The current standards, API SP and ILSAC GF-6A, and approvals like Dexos1 Gen 3, all test for wear and deposits. Our guide to the letters on the oil jug explains what each one means.
  • Drive gently for the first few miles. Most modern owner's manuals say to wait a few seconds after starting and then drive off at moderate speed, rather than idling for a long time or revving a cold engine. Light driving warms the oil faster than idling does.
  • Combine short trips when you can. One twenty-minute loop is easier on the oil than four five-minute ones.
  • Plug in the block heater if you have one. On the coldest mornings, warm coolant around the engine means the oil is less cold too, and the engine turns over more easily.
  • Watch the oil pressure light. It should go out within a couple of seconds of starting. If it stays on, shut the engine off and check the level before driving.

Where we come in

Every oil change we do is full synthetic, licensed to API SP, ILSAC GF-6A, and Dexos1 Gen 3, in the viscosity your engine calls for, with a new filter. That covers the oil side of a cold start.

We work weekdays from 9am to 5pm at homes and workplaces in Cedar Rapids, Marion, Hiawatha, and Robins. You leave the keys, and the car is done when you come back to it. What is included, and what we do not do, is on the pricing page and in the FAQ.

CallBook Now